7 results found
-
Sensor dropped out
Both Garmin ANT+ heartrate monitor and 4iiii cadence dropped out during workout. Restarted and TPV crashed. Rebooted laptop and now Kickr not receiving ERG resistance correctly. Windows OS
1 voteMany thanks for letting us know about this, and your support for TrainingPeaks Virtual.
This is a bug in the latest release that impacts sensors if they disconnect (and then automatically reconnects) whilst you are riding. We already have a fix and this will be available in the next release out next week.
-
wahoo speed sensor
Wahoo Speed Sensor recognized but does not register while pedaling. It was working great until the latest update
1 voteMany thanks for letting us know about this, and your support for TrainingPeaks Virtual.
This is a bug in the latest release that impacts sensors if they disconnect (and then automatically reconnects) whilst you are riding. We already have a fix and this will be available in the next release out next week.
-
Garmin speedometer (Bug) no longer registers wattage
My garmin speedometer (Speed Sensor 2) still connected, but stopped registering wattage today leaving me at a literal standstill while using my "dumb" rollers. The cadense sensor continued to work just fine. It had been working correctly as of 1/9/25
3 votesMany thanks for letting us know about this, and your support for TrainingPeaks Virtual.
This is a bug in the latest release that impacts sensors if they disconnect (and then automatically reconnects) whilst you are riding. We already have a fix and this will be available in the next release out next week.
-
FTP Test (ramp) Bug
After reaching the fail point on the TPV ramp test workout today, the ERG mode wouldn't release. It seemed like it had, but as soon as my cadence reached 70rpm, the resistance kicked up, meaning I was over 300W despite target power saying 100 or 150W (I couldn't see at this point!). Latest version of TPV running on iPad and 1st gen WattBike Atom.
1 voteMany thanks for letting us know about this, and your support for TrainingPeaks Virtual.
This is a bug in the latest release that impacts ERG mode workouts if your trainer disconnects (and then automatically reconnects) whilst you are riding. We already have a fix and this will be available in the next release out next week.
-
Power control in structured workouts has stopped working.
TPV no longer holds the required power in workouts. I have a choice of power meter options - Kickr or power meter on the bike. In structured workouts, the TPV system hits the required power briefly then drops to 50 to 70 Watts. Same result for whichever of the power devices I have paired. I have done multiple re-runs after complete shut down but I can't get the system to properly run power in my structured workouts. System is all working fine on the Zwift platform.
6 votesMany thanks for letting us know about this, and your support for TrainingPeaks Virtual.
This is a bug in the latest release that impacts ERG mode workouts if your trainer disconnects (and then automatically reconnects) whilst you are riding. We already have a fix and this will be available in the next release out next week.
-
Controlable not working after update
In the last update, a change was made so that only all sensors would work. However, it turns out that some manufacturers not approved for TPV stopped allowing the controllable feature of the smart trainer to function. How should we proceed in this case, as only the power sensor works, and previously there was inertia when starting a climb, for example?
2 votesMany thanks for letting us know about this, and your support for TrainingPeaks Virtual.
This is a bug in the latest release that impacts ERG mode workouts if your trainer disconnects (and then automatically reconnects) whilst you are riding. We already have a fix and this will be available in the next release out next week.
-
Emparelhamento sensores
Hello, I installed virtual trainingpeaks on my android phone and did several workouts that I liked. I managed to pair all the sensors, heart, cadence and power (speed). Everything worked well until I updated the application. Now I can pair all the sensors except the one for power (speed). It detects the sensor and pairs but it does not go beyond 0 (zero), whereas before this sensor worked well giving me speed and power. Is there anything you can do to resolve this situation? your response. Thank you
1 voteMany thanks for letting us know about this, and your support for TrainingPeaks Virtual.
This is a bug in the latest release that impacts sensors if they disconnect (and then automatically reconnects) whilst you are riding. We already have a fix and this will be available in the next release out next week.
- Don't see your idea?